Fax Machines (Specific Models) That Work With Vonage

Posts: 7 · New Forum Member Joined: Jun 10, 2005 Posts: 7

LMari wrote:

Sharp UX-B700 works fine.

I have this same fax machine and it works once in a while, but not very consistantly. Keep getting line error messages back. Did you have to change any setting to get it to work every time? I have read the manual and so on and didn't see a way to change the baud rate, however I did install a dsl filter but it didn't seem to help. Any suggesions anyone?

Posts: 1 · New Forum Member Joined: Dec 28, 2005 Posts: 1

I also have problems with faxing using Vonage; my fax system is a Epson CX11NF, which doesn't come with the option of turning off ECM or forcing the rate down to 9600. Yet, it seems that doesn't help much of you also. I am trying some diffrent tested tonight to see if I can resolve the problem; I find it funny to be on the cutting (bleeding) edge of VOIP but with a 1980's faxing technology limit!

I think that they are being cheap and not offering a more stable codex and bit settings for faxes. It would be nice to offer the ability to use better hardware that gives the techy end-users and corporates more access to changing the voice settings.

Later,
Danny D

---
Dual Internet with life-fail-over (6Mbx2Mb Cable and 2Mbx2Mb DSL) > WatchGuard Firebox IIIR > DMZ_PORT > Cisco Catalyst 2960 Switch {Advanced QoS + POE} > LinkSys RT31P2 {Four} > Aastra Venture IP Enterprise VOIP PBX {8-Ports, 16-Extentions} | Catalyst Setup with two VLANS, one for the DMZ and LinkSys units, one for the Aastra VOIP Phones.

Posts: 1 · New Forum Member Joined: Oct 23, 2005 Posts: 1

I have a cheapo Sharp UX-305 that seems to work 80% of my tries, but only after using *99 first.

Posts: 1 · New Forum Member Joined: Jan 16, 2006 Posts: 1

I am having a problem with some faxes. The Vonage line seems to fax well when using a fax from the computer (Brother Fax) but the machine to which the fax is sent does not respond or seems to hang up before the fax is sent. This is a problem only with some faxes not all. Does anyone know the reason for this and, if so, is there a correction available?

Posts: 1123 · Vonage Forum **MVM** Joined: May 26, 2005 Posts: 1123

Sorry if it was already mentioned: HP Officejet 5510v works very well with Vonage.

Posts: 409 · Posted: Tue Jan 17, 2006 7:51 pm Post subject:

I use a Canon MultipassC755 and it works wonderfully with my Vonage I have it plugged in a plugin adapter ( two lines plugged in sharing one phone port) works like a charm Wink

Posts: 2 · New Forum Member Joined: Jan 18, 2006 Posts: 2

I have tried just about everything trying to get my fax machine to work, still not luck. I called tech support 2 days in a row for at least 1 hour to an hour1/2 each call, still no luck. I just went and got a new fax hp 1050 still not able to send or receive. I saw some posts talking about the phone adapter. My model is the RT31p2 is there an updated adapter I could be using that works better? if so which is the best? Any help appreciated.

Posts: 409 · Posted: Wed Jan 18, 2006 10:30 am Post subject:

HI lilmrk,

First it might help in reading this link vonage-forum.com/ftopic7191.html" target="_blank">http://www.vonage-forum.com/ftopic7191.html Then posting the information. There are some very knowledgable people on this forum that are willing to help.

Posts: 2 · New Forum Member Joined: Jan 18, 2006 Posts: 2

No Problem!

_________________
Location.....Michigan
isp..............Wideopenwest
Voip............Vonage
Router.........Linksys RT31P2
Fax Machine..hp 1050

Posts: 1 · New Forum Member Joined: Jan 23, 2006 Posts: 1

HP OfficeJet R80 all-in-one works with Vonage if you go to the Service Setup menu and select Reduced baud for all faxes... it would not work without this change. Have successfully faxed with this setting.

----------------------
Location - Texas
ISP - Roadrunner
Router - Linksys WRTP54G
VOIP - Vonage