Nokia E- Series and Softphone

Posts: 3 · New Forum Member Joined: Aug 20, 2003 Posts: 3

Please has anyone successfully configured the SIP in any of the Nokia E- Series phone who can share the config settings with me? I would very much appreciate any help.

Posts: 8 · New Forum Member Joined: Aug 23, 2007 Posts: 8

Tools--> Settings-->Connection-->SIP Settings

Profile Name: Vonage (Or what ever you choose.)
Service profile: IETF
Default access point: (Choose what ever is applicable to you)
Public user name: sip:(1+ your Vonage softphone number)@sphone.vonage.net
Use compression: No
Registration: (Choose what ever is applicable to you)
Use security: No

Proxy server

Proxy server address: None
Realm: 216.115.20.41
User name: (1+ your Vonage softphone number)
Password: (Your password)
Allow loose routing: Yes
Transport type: Auto
Port: 5060

Registrar Server

Registrar server address: sip:sphone.vopr.vonage.net
Realm: sphone.vopr.vonage.net
User name: (1+ your Vonage softphone number)
Password: (Your password)
Transport type: UDP
Port: 5060

Posts: 2 · New Forum Member Joined: Aug 25, 2007 Posts: 2

I have a Nokia E90 and was very happy to see this information! I configured the Nokia and tried to make a Voip call but I am just getting a "Registration Failed". Has anybody had luck with this setup?

Posts: 8 · New Forum Member Joined: Aug 23, 2007 Posts: 8

Sorry for the change; it appears that the SIP client in the N series is a different ver (maybe). This config should work on either; if you get a registration failed then check your username and password on the Vonage website. Make sure you have a working access point (WiFi or GPRS) before you try to register the connection.

Tools--> Settings-->Connection-->SIP Settings

Profile Name: Vonage (Or what ever you choose.)
Service profile: IETF
Default access point: (Choose what ever is applicable to you)
Public user name: sip:(1+ your Vonage softphone number)@sphone.vonage.net
Use compression: No
Registration: (Choose what ever is applicable to you)
Use security: No

Proxy server

Proxy server address: None
Realm: 216.115.20.41
User name: (1+ your Vonage softphone number)
Password: (Your password)
Allow loose routing: Yes
Transport type: Auto
Port: 5060

Registrar Server

Registrar server address: sip:sphone.vopr.vonage.net
Realm: 216.115.20.41
User name: (1+ your Vonage softphone number)
Password: (Your password)
Transport type: UDP
Port: 5061

Posts: 2 · New Forum Member Joined: Aug 25, 2007 Posts: 2

Lanrover wrote:

Transport type: UDP
Port: 5061

Thanks LANRover.... I rechecked my settings information for the softphone as sent by Vonage and noticed that they referenced port 5061. I changed both the port numbers to 5061 and noticed the I was now getting a "Registered" message. When I tried to call somebody though the E90 would act as if the call is going through but the other phone just would not ring...

Based on your second post I played around a bit... I changed the Transport Type to UDP and all port numbers to 5060. It refreshed the screen and showed as "Registered". I called myself on the other land line and suddenly it worked. I played around with the port settings and swapped between 5060 and 5061 and it always worked. I changed the Transport Type back to auto and everything failed.

So I think it is important to point out that the Transport Type has to be UDP under the Registrar Server.

Thanks for the trouble.

Posts: 3 · New Forum Member Joined: Aug 20, 2003 Posts: 3

Thanks for the proffered solutions but when I tried the 2 sets of steps, my E90 communicator still didn't register.

Posts: 1 · New Forum Member Joined: Mar 31, 2008 Posts: 1

Any update on this thread - Followed all the recommendations above, phone states that I am registered. I for one being new at this can't seem to figure out how to place a SIP call from my E90, two, I tried to call my phone using my SIP number and the phone just freezes up -

Any recommendation greatly appreciated -

TS