| Author |
Message |
| Topic: audio cutting out |
ntravisano
Replies: 10
Views: 1230
|
 Forum: Vonage Forum Archive
Posted: Fri Sep 01, 2006 8:18 am Subject: 5.4ghz phones are known to use a dual channel at 2.4ghz. they are still known to |
| 5.4ghz phones are known to use a dual channel at 2.4ghz. they are still known to interfere with the 2.4 ghz devices. |
| Topic: Vonage TA Cannot initialize. tftp file error |
ntravisano
Replies: 8
Views: 1738
|
Forum: Vonage Forum Archive
Posted: Fri Sep 01, 2006 8:13 am Subject: go in and do a factory reset on the device. this is an issue with the firmware that |
| go in and do a factory reset on the device. this is an issue with the firmware that was pushed last friday. Also as a note remove the WAN cable from the vt1005 before you try to connect to the web int ... |
| Topic: audio cutting out |
ntravisano
Replies: 10
Views: 1230
|
Forum: Vonage Forum Archive
Posted: Thu Aug 31, 2006 2:27 pm Subject: Try changing the channel that the cordless phone is on also. 5.4GHZ does not always |
| Try changing the channel that the cordless phone is on also. 5.4GHZ does not always transmit at that transmission it drops to 2.4GHZ alot of the times. |
| Topic: Audio Cutting out again |
ntravisano
Replies: 14
Views: 1509
|
Forum: Vonage Forum Archive
Posted: Thu Aug 31, 2006 2:24 pm Subject: Sounds to me like you are dropping packets somewhere along your transmission. |
| Sounds to me like you are dropping packets somewhere along your transmission. Have you tried running a ping and/or some tracerts to see if you are getting any heavy latency on any of the servers that ... |
| Topic: Pap2 v2 firmware won't upgrade |
ntravisano
Replies: 4
Views: 3748
|
Forum: Vonage Forum Archive
Posted: Sat Aug 26, 2006 4:41 am Subject: PAP2v2 was just released.. To my knowledge their is no newer firmware out for that |
| PAP2v2 was just released.. To my knowledge their is no newer firmware out for that version of that adapter. The original PAP2 is at that stage of firmware I believe.. |
| Topic: Newbie: Choppy Audio |
ntravisano
Replies: 6
Views: 638
|
Forum: Vonage Forum Archive
Posted: Sat Aug 26, 2006 4:37 am Subject: FYI if you are able to do port forwarding on the belkin router I would advise doing |
| FYI if you are able to do port forwarding on the belkin router I would advise doing that also, Assign a stick IP for the PAP2. (it is in the manual and done from the phone's IVR system) Bandwidth save ... |
| Topic: Must reset phone adaptor and/or router daily. |
ntravisano
Replies: 9
Views: 2202
|
Forum: Vonage Forum Archive
Posted: Sat Aug 26, 2006 4:33 am Subject: http://www.portforward.com
go there also after making a static IP and make |
http://www.portforward.com
go there also after making a static IP and make sure all the ports needed for VOIP are forwarding to that static IP. Another thing to look into is if you are going to pi ... |
| Topic: No dial tone |
ntravisano
Replies: 32
Views: 3873
|
Forum: Vonage Forum Archive
Posted: Sat Aug 26, 2006 4:27 am Subject: FYI with the Motorola vt1005 and it hanging at 4 blinking lights... Vonage rolled |
| FYI with the Motorola vt1005 and it hanging at 4 blinking lights... Vonage rolled out a new firmware from Motorola on Friday. The servers that the 1005 were receiving the files were having issues with ... |
| Topic: Using Vonage with Planet SHDSL Bridge Router GRT-101 |
ntravisano
Replies: 5
Views: 749
|
Forum: Vonage Forum Archive
Posted: Fri Aug 25, 2006 7:15 am Subject: You need to apply PPPOE settings in the setup page for the motorola vt2442 adapter. |
| You need to apply PPPOE settings in the setup page for the motorola vt2442 adapter. You most likely had those settings setup on your PC at first. You said the DSL modem is a bridge correct and is not ... |
| |
Members
New 
New Today 7
Yesterday 18
Total 63405
Who Is On Site
Visitors 211
Members 0
Total 211
+0.091