 |
 | Vonage Forum Menu |
| | |
| Vonage Forums |
|
|
| | | |
| Vonage In The News |
| | |
| Vonage Customer Reviews |
| | |
| |
Vonage It is a single computer hooked up through my Comcast cable/internet line. Like
It is a single computer hooked up through my Comcast cable/internet line. Like I said, no problems before until I reboot. I was going in to configure the router in order to get to the screen that asks me to type in admin for the name and password and the website is not working.
Here is the reply I got from Vonage this morning (which did not help, they thought I transposed a number but I have not been):
Dear Toby Hilden,
Thank you for contacting Customer Care.
The IP address of the router is 192.168.15.1 but not 192.168.51.1. So
please follow the instructions given below to troubleshoot the issue:
1. Open internet explorer from one of the computers connected to the RT31P2 router and in the address bar, type http://192.168.15.1 and
press Enter.
2. Enter "admin" in both username and password fields when it prompts and click on "Ok". 3. Click on the tab "Administration" and click on sub-tab "Factory Defaults". Now select "Restore factory defaults" as "yes" and click on "Save Settings". It should display "Settings are Successful". 4. Then it will ask to enter User name and password. So enter as follows User name : user Password : 7756112 5. Once this is done, disconnect power cable from all the devices in the network which includes modem, router and RT31P2. 6. Connect the appropriate power cable to the cable modem. 7. Wait about two minutes for the cable modem to boot up, before continuing. 8. Connect the power cable, provided with the Phone Adapter, to the
power port on the Phone Adapter.
9. Wait about two minutes for the phone adapter to boot up before continuing. 10. Open Internet Explorer and in the address bar type "192.168.15.1" and hit enter 11. Enter admin as user name and password when it prompts and click "OK"
Now click on the "Status" tab and then on the "router" sub-tab, now check for the Internet IP address, If you get an IP address, try to go online. If the Internet IP address is all zeroes, click on DHCP Renew. If you get an IP address, try to go online.
If the IP Address is still all zeroes, then Click on "Setup" tab and then click on "MAC Address Clone" sub-tab. Select "Enable" under MAC Clone Service and then click on "Clone". Now click on "Save Settings".
Now click on the "Status" tab and then on the "router" sub-tab, now check for the Internet IP address, If you get an IP address, try to go online. If the Internet IP address is all zeroes, Click on DHCP Renew. If you get an IP address, try to go online.
12. If you are able to go online, connect a telephone to the "Phone 1" port of the Phone Adapter using a standard phone line. 13. Wait at least five minutes for the Phone Adapter to boot up. The
Phone Adapter's lights will remain off or blink until it is fully
connected to the Vonage network. There may be updates that need to be
downloaded such as new firmware or changes to your features. Do not
interrupt the configuration process by unplugging the power or lifting
the receiver on your phone during the startup process. Interruption of
the startup may result in interruption of service.
14. Once the Phone Adapter's status light is off, the Phone Adapter is ready to use. 15. Pick up your telephone receiver and listen for a dial tone. If you hear a dial tone, you can start making and receiving calls.
We hope this has assisted you in resolving the issue. If after
following these above steps you are still experiencing trouble, please
reply to this email and we will be sure to assist you further.
We value you as a customer and are dedicated to quality customer
service.
Regards,
Kanchan.
Customer Care.
Read The Full Thread: http://192.168.15.1
• I had to reboot tonight and set up Vonage again. I tried to go into step 2: COnfigure
• does vonage send out used routers? i dont see any reason why that address wouldnt
• This was a brand new one- I had the vonage system working fine for 5 weeks until I
• you don't need the cd or anything like that. it should be plug n play more or less.
• so your network setup is cable modem (which one) to the lnksys rt31p2 to your computer
• The lights on the router are as follows:
Power: Solid green
Ethernet 1:
• ok, I still don't have a clear picture of your setup. just write it out.
cable
• I'll do my best (and thank you in advance for you patience and help)...
Cable
• Try it without the http maybe. just the numbers.
tobyhilden posted "It is a single computer hooked up through my Comcast cable/internet line. Like" on 08/14/2005 |
|
|
| |
| Vonage Service Plans |
| | |
| Vonage VoIP Members |
|
 Members
 New Dave159
 New Today 0
 Yesterday 3
 Total 64291
 Who Is On Site
 Visitors 84
 Members 0
 Total 84
Vonage VoIP Forum Members:
Login Here
Not a Member? You can Register Here
As a registered member you will have access to the VoIP Speed Test, Vonage Service Announcements and post comments in the
Vonage VoIP Forums | | | |
| Vonage Stock Price |
|
Value: 1.70
Change:  -0.03
Up to 15 Minute Delay | | | |
| Site Search |
| | |
|
|
Vonage VoIP Phone Service is redefining communications by offering consumers
& small business VoIP Internet phones, an affordable alternative to traditional phone service.
The Vonage VoIP Forum Generated This Page In: 0.33 Seconds and 299 Pages In The Last 60 Seconds
The Vonage VoIP Forum
|
