 |
 | Vonage Forum Menu |
| | |
| Vonage Forums |
|
|
| | | |
| Vonage In The News |
| | |
| Vonage User Reviews |
| | |
| |
Vonage I don't have an RTP300, but I'll try to give some ideas here....
I read this
I don't have an RTP300, but I'll try to give some ideas here....
I read this as the RTP300 worked "prior" to the ISA2004 Install. You now unplugged the RTP300 and setup an ISA2004 server in it's place. If this is the case, ISA2004, when initialy installed doesn't have any outbound, or Publish server, rules setup, so any traffic that hits it, outbound or inbound,won't "flow" through the ISAServer
You'll need to create a "Publish Server" rule on ISA to forward traffic from the external interface on the ISA Server to the internal IP address that you've manually assigned to the WAN interface of your RTP300. You should only have to plug the WAN interface into your internal swtich. The other LAN port should stay unplugged, and then you plug your phones into the jacks on the RTP300. You'll also need to create an outbound rule for traffic. Depending on how "locked" down you want this, but you need rule to either allow all traffic, or specific ports for any traffic coming from the statically assigned IP address on the WAN interface of the RTP300.
I've included the ports needed to make this happen below, here's a link to url: Port Forwarding , but here's the info below if you do want to get specific:
These are the ports that Vonage requires to be OPEN for successful use of the Vonage device (the ability to make and receive calls, download device profiles, firmware, etc). Under most circumstances these ports are already opened or allowed. You must be careful to not inadvertently close them.
The following ports are needed for OUTGOING Internet communications from the Vonage device to the Vonage servers.
DNS: Port 53 UDP (Domain Name Server - for resolving server IP addresses)
TFTP: Port 69 UDP (for profile upgrades/downgrades)
HTTP: Port 80 UDP (for firmware upgrades/downgrades)
NTP: Port 123 UDP (Network Time Protocol - so the device can sync to the proper time for Caller ID)
SIP: Port 5061 UDP is used for older Vonage devices (devices provisioned before 2005) Also, BSP Proxy Groups 1-8, and a.voncp.com communicate on port 5061.
The following ports are needed for INCOMING and OUTGOING Internet communications from and to Vonage devices and servers.
RTP (Voice) Traffic: Ports 10000-20000 UDP. When a call is made, a random port between 10000 and 20000 is used for RTP (Voice) traffic. If any of these ports are blocked, you may experience one way or no audio
Hope this helps!!!!!
Read The Full Thread: RTP300 behind ISA2004 Firewall having issues
• I have the RTP300 behind an ISA2004 Firewall. It was working until I unplugged
• So do you have a dialtone?
Have you tried doing a hard reset to the RTP300 (back
• Thank you for your response. The phone plugged into the RTP300 does not have a dialtone
• Any port forwards? DMZ? Odd that it's provisioned but no phone LED.
• You ask "Any Ports Forwarded" If you are refering to the RTP300 all Firewall functionality
rozy posted "I don't have an RTP300, but I'll try to give some ideas here....
I read this" on 11/21/2005 |
|
|
| |
| Vonage Service Plans |
| | |
| Vonage VoIP Members |
|
 Members
 New annamr
 New Today 4
 Yesterday 6
 Total 55100
 Who Is On Site
 Visitors 198
 Members 1
 Total 199
Vonage VoIP Forum Members:
Login Here
Not a Member? You can Register Here
As a registered member you will have access to the VoIP Speed Test, Vonage Service Announcements and post comments in the
Vonage VoIP Forums | | | |
| Vonage Stock Price |
|
Value: 1.16
Change:  -0.04
Up to 15 Minute Delay | | | |
| Site Search |
| | |
|
|
Vonage VoIP Phone Service is redefining communications by offering consumers
& small business VoIP Internet phones, an affordable alternative to traditional phone service.
The Vonage VoIP Forum Generated This Page In: 0.33 Seconds and 216 Pages In The Last 60 Seconds
The Vonage VoIP Forum
|
